Showing 17–31 of 31 results
-
$94.50 / Pack
Multifiber Fabric #1 is a multifiber fabric with approximately 8 mm (0.33 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, silk, viscose, and worsted wool yarns, woven on a warp of filament polyester. Available as 2″x4″ precut pieces, Multifiber Fabric #1 with heat sealed edges can be used in dynamic
AATCC colorfastness tests that involve agitation and movement of the test pieces. Heat Sealed multifiber fabrics have a melted or fused edge, which reduces fraying and increases stability in the multifiber fabric test fabric. In AATCC colorfastness testing, heat sealed multifiber fabrics are used primarily to evaluate potential staining of a dyed or printed test sample on other textiles in wash tests where the test material experiences agitation and movement during the testing process. Multifiber fabrics with heat sealed edges should not be used in stationary tests because the raised melted edge can cause uneven
staining between the multifiber fabric and test specimen, and results cannot be guaranteed.
-
$627.75 / Roll
Multifiber Fabric #10 is a multifiber fabric with approximately 8 mm (0.33 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester.
The 3/8” wide filling stripes of the six predominant apparel fibers, woven in a two inch repeat and with a ‘separator/cutting/ waste’ stripe between each of the two inch repeats of the six fiber stripes to allow for cutting of consistent test specimens.
Note: Testfabrics, Inc. does not accept any returns if any errors occur during cutting. For precision, consistency and efficiency we recommend MFF PRECUT PIECES available in Cold Cut Edges, Heat Sealed Edges & Overcast Edges.
-
$37.75 / Pack
Multifiber Fabric #10A is a multifiber fabric with approximately 15 mm (0.6 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester. The 15mm / 0.6” wide filling stripes of the six predominant apparel fibers, are woven in a four inch
repeat and with a ‘separator/cutting/ waste’ stripe, between each of the four inch repeats, of the six fiber stripes, allows for cutting of consistent test specimens.
Note: Testfabrics, Inc. does not accept any returns, if any error occurs during cutting. For precision, consistency and efficiency we recommend MFF PRECUT PIECES available in Cold Cut Edges, Heat Sealed Edges & Overcast Edges.
-
$182.25 / Pack
Multifiber Fabric #10A is a multifiber fabric with approximately 15 mm (0.6 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester. The 15mm / 0.6” wide filling stripes of the six predominant apparel fibers, are woven in a four inch
repeat and with a ‘separator/cutting/ waste’ stripe, between each of the four inch repeats, of the six fiber stripes, allows for cutting of consistent test specimens.
Note: Testfabrics, Inc. does not accept any returns, if any error occurs during cutting. For precision, consistency and efficiency we recommend MFF PRECUT PIECES available in Cold Cut Edges, Heat Sealed Edges & Overcast Edges.
-
$31.75 / meter
Multifiber Fabric #10 is a multifiber fabric with approximately 8 mm (0.33 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester.
The 3/8” wide filling stripes of the six predominant apparel fibers, woven in a two inch repeat and with a ‘separator/cutting/ waste’ stripe between each of the two inch repeats of the six fiber stripes allows for cutting of consistent test specimens.
Note: Testfabrics, Inc. does not accept any returns if any error occurs during cutting. For precision, consistency and efficiency we recommend MFF PRECUT PIECES available in Cold Cut Edges, Heat Sealed Edges & Overcast Edges.
-
$138.25 / Pack
Multifiber Fabric #10 is a multifiber fabric with approximately 8 mm (0.33 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester.
The 3/8” wide filling stripes of the six apparel fibers, woven in a two inch repeat and with a ‘separator/cutting/ waste’ stripe between each of the two inch repeats of the six fiber stripes to allow for cutting of consistent test specimens.
Note: Testfabrics, Inc. does not accept any returns if any error occurs during cutting. For precision, consistency and efficiency we recommend MFF PRECUT PIECES available in Cold Cut Edges, Heat Sealed Edges & Overcast Edges.
-
$878.75 / Roll
Multifiber Fabric #10A is a multifiber fabric with approximately 15 mm (0.6 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester. The 15mm / 0.6” wide filling stripes of the six predominant apparel fibers, are woven in a four inch
repeat and with a ‘separator/cutting/ waste’ stripe, between each of the four inch repeats, of the six fiber stripes, allows for cutting of consistent test specimens.
Note: Testfabrics, Inc. does not accept any returns, if any error occurs during cutting. For precision, consistency and efficiency we recommend MFF PRECUT PIECES available in Cold Cut Edges, Heat Sealed Edges & Overcast Edges.
-
$100.50 / Pack
Multifiber Fabric #1, is a multifiber fabric with approximately 8 mm (0.33 inch) filling stripes of 6 fibers,
acetate, bleached cotton, nylon, silk, viscose, and worsted wool yarns, woven on a warp of filament polyester. Available as 2″x2″ precut pieces with cold cut edges. Multifiber Fabric #1 with cold cut edges should only be used in static AATCC colorfastness tests. Cold cut multifiber fabrics have a clean level edge. In AATCC colorfastness testing, cold cut multifiber fabrics are used to evaluate potential staining of a test sample on other textiles in stationary colorfastness testing scenarios. Multifiber fabric with cold cut edges will fall apart if they are used with agitation or in a laundrometer under mechanical action.
-
AATCC UV Calibration Reference Fabric, includes certificate.
-
/ Pack
White cards (specimen mounts) with Y tristimulus value at least 85%.
-
$81.75 / Pack
Multifiber Fabric #10, is a multifiber fabric with approximately 8 mm (0.33 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester. Available as 2″x4″ precut pieces with cold cut edges. Multifiber Fabric #10 with cold cut edges should only be used in static AATCC colorfastness tests. Cold cut multifiber fabrics have a clean level edge. In AATCC colorfastness testing, cold cut multifiber fabrics are used to evaluate potential staining of a test sample on other textiles in stationary colorfastness testing scenarios. Multifiber fabric with cold cut edges will fall apart if they are used with agitation or in a laundrometer under mechanical action.
-
$88.00 / Pack
Multifiber Fabric #10 is a multifiber fabric with approximately 8 mm (0.33 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester.
Available as 2″x2″ precut pieces, Multifiber Fabric #10 with overcast serged edges are heat sealed along the waste stripes and overcast stich serged along the filling stripes. This type of added edge finish prevents fraying and gives the multifiber test piece added stability. It can be used in rigorous colorfastness testing situations and is recommended for any tests that subject the multifiber fabric to increased agitation and movement.
In AATCC colorfastness testing, heat sealed and overcast serged multifiber fabrics are used primarily to evaluate potential staining of a dyed or printed test sample on other textiles in wash tests where the test material experiences agitation and movement during the testing process. Multifiber fabrics with heat sealed edges should not be used in stationary tests because the raised melted edge can cause uneven staining between the multifiber fabric and test specimen.
-
$63.00 / box
Multifiber Fabric #10A is a multifiber fabric with approximately 15 mm (0.6 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester. Available as 4cm x 10cm precut pieces, Multifiber Fabric #10A with overcast serged edges are heat
sealed along the waste stripes and overcast stich serged along the filling stripes. This type of added edge finish prevents fraying and gives the multifiber test piece added stability. It can be used in rigorous colorfastness testing situations and is recommended for any tests that subject the multifiber fabric to increased agitation and movement. In AATCC and ISO colorfastness testing, heat sealed and overcast serged multifiber fabrics are used primarily to evaluate potential staining of a dyed or printed test sample on other textiles in wash tests where the test material experiences agitation and movement during the testing process. Multifiber
fabrics with heat sealed and overcast edges should not be used in stationary tests because the raised and melted edge can cause uneven staining between the multifiber fabric and test specimen.
-
/ Piece
Rub A Dub laundry marking pen
-
$75.50 / Pack
Multifiber Fabric #10 is a multifiber fabric with approximately 8 mm (0.33 inch) filling stripes of 6 fibers, acetate, bleached cotton, nylon, polyester, acrylic, and worsted wool yarns, woven on a warp of filament polyester.
Available as 2″x4″ precut pieces, Multifiber Fabric #10 with heat sealed edges can be used in dynamic AATCC colorfastness tests that involve agitation and movement of the test pieces. Heat Sealed multifiber fabrics have a melted or fused edge, which reduces fraying and increases stability in the multifiber fabric test fabric.
In AATCC colorfastness testing, heat sealed multifiber fabrics are used primarily to evaluate potential staining of a dyed or printed test sample on other textiles in wash tests where the test material experiences agitation and movement during the testing process. Multifiber fabrics with heat sealed edges should not be used in stationary tests because the raised melted edge can cause uneven staining between the multifiber fabric and test specimen, and results cannot be guaranteed.
End of content
End of content
